Exhibit 6: Residential Square Footage Guidelines

Exhibit 6: Residential Square Footage Guidelines


It is often said that the three most important factors in making a home buying decision are "location," "location," and "location." Other than "location," the single most-important factor is probably the size or "square footage" of the home. Not only is it an indicator of whether a home will meet a homebuyer's space needs, but it also affords a convenient (though not always accurate) method for the buyer to estimate the value of the home and compare it with other properties.

Although real estate agents are not required by the Real Estate License Law or Real Estate Commission rules to report the square footage of properties offered for sale (or rent), when they do report square footage, it is essential that the information they give prospective purchasers be accurate. At a minimum, information concerning square footage should include the amount of living area in the dwelling. The following guidelines and accompanying illustrations are designed to assist real estate brokers and salespersons in measuring, calculating and reporting (both orally and in writing) the living area contained in detached and attached single-family residential buildings. When reporting square footage, real estate agents should carefully follow these Guidelines or any other standards that are comparable to them, including those approved by the American National Standards Institute, Inc. (ANSI) which are recognized by the North Carolina Real Estate Commission as comparable standards. * Agents should be prepared to identify, when requested, the standard used.

Living Area Criteria

Living area (sometimes referred to as "heated living area" or "heated square footage") is space that is intended for human occupancy and is:

1. Heated by a conventional heating system or systems (forced air, radiant, solar, etc.) that are permanently installed in the dwelling - not a portable heater - which generates heat sufficient to make the space suitable for year-round occupancy;

2. Finished, with walls, floors and ceilings of materials generally accepted for interior construction (e.g., painted drywall/sheet rock or paneled walls, carpeted or hardwood flooring, etc.) and with a ceiling height of at least seven feet, except under beams, ducts, etc. where the height must be at least six feet four inches [Note: In rooms with sloped ceilings (e.g., finished attics, bonus rooms, etc.) you may also include as living area the portion of the room with a ceiling height of at least five feet if at least one-half of the finished area of the room has a ceiling height of at least seven feet.]; and

3. Directly accessible from other living area (through a door or by a heated hallway or stairway).

Real estate appraisers and lenders generally adhere to more detailed criteria in arriving at the living area or "gross living area" of residential dwellings. This normally includes distinguishing "above-grade" from "below-grade" area, which is also required by many multiple listing services. "Above-Grade" is defined as space on any level of a dwelling which has living area and no earth adjacent to any exterior wall on that level. "Below-Grade" is space on any level which has living area, is accessible by interior stairs, and has earth adjacent to any exterior wall on that level. If earth is adjacent to any portion of a wall, the entire level is considered "below-grade." Space that is "at" or "on grade" is considered "above-grade."

While real estate agents are encouraged to provide the most complete information available about properties offered for sale, the Guidelines recognize that the separate reporting of "above-grade" and "below-grade" area can be impractical in the advertising and marketing of homes. For this reason, real estate agents are permitted under these Guidelines to report square footage of the dwelling as the total "living area" without a separate distinction between "above-grade" and "below-grade" areas. However, to help avoid confusion and concern, agents should alert purchasers and sellers that the appraisal report may reflect differences in the way living area is defined and described by the lender, appraiser, and the North Carolina Building Code which could affect the amount of living area reported.

Determining whether an area is considered living area can sometimes be confusing. Finished rooms used for general living (living room, dining room, kitchen, den, bedrooms, etc.) are normally included in living area. For other areas in the dwelling, the determination may not be so easy. For example, the following areas are considered living area if they meet the criteria (i.e., heated, finished, directly accessible from living area):
  1. Attic, but note in the listing data that the space is located in an attic (Fig. 2). [Note: If the ceiling is sloped, remember to apply the "ceiling height" criteria.]
  2. Basement(or "Below-Grade"), but note in the listing data that the space is located in a basement or "below-grade" (Fig. 1). [Note: For reporting purposes, a "basement" is defined as an area below the entry level of the dwelling which is accessible by a full flight of stairs and has earth adjacent to some portion of at least one wall above the floor level.]
  3.  Bay Window, if it has a floor, a ceiling height of at least seven feet, and otherwise meets the criteria for living area (Fig. 2).
  4. Bonus Room(e.g., Finished Room over Garage) (Fig. 3). [Note: If the ceiling is sloped, remember to apply the "ceiling height" criteria.]
  5. Breezeway (enclosed).
  6. Chimney, if the chimney base is inside living area. If the chimney base is outside the living area but the hearth is in the living area, include the hearth in the living area but not the chimney base (Fig. 1).
  7. Closets, if they are a functional part of the living area.
  8. Dormers (Fig. 6).
  9. Furnace (Mechanical) Room Also, in order to avoid excessive detail, if the furnace, water heater, etc. is located in a small closet in the living area, include it in living area even if it does not meet other living area criteria (Fig. 4).
  10. Hallways, if they are a functional part of the living area.
  11. Laundry Room/Area (Fig. 6)
  12. Office (Fig. 1).
  13. Stairs, if they meet the criteria and connect to living area (Fig. 1, 2, 3, 4, 5, 6). Include the stairway with the area from which it descends, not to exceed the area of the opening in the floor. If the opening for the stairway exceeds the length and width of the stairway, deduct the excess open space from the upper level area. Include as part of the lower level area the space beneath the stairway, regardless of its ceiling height.
  14. Storage Room(Fig. 6).
View Attachments for Figures
Note in the listing data and advise purchasers of any space that does not meet the criteria for living area, but which contributes to the value of the dwelling; for example, unfinished basements, unfinished attics (with permanent stairs), unfinished bonus rooms, shops, decks, balconies, porches, garages and carports.

Helpful Hints

Concealed in the walls of nearly all residential construction are pipes, ducts, chases, returns, etc. necessary to support the structure's mechanical systems. Although they may occupy living area, to avoid excessive detail, do not deduct the space from the living area.

When measuring, and reporting the living area of homes, be alert to any remodeling, room additions (e.g., an enclosed porch) or other structural modifications to assure that the space meets all the criteria for living area. Pay particular attention to the heating criteria, because the heating system for the original structure may not be adequate for the increased square footage. Although agents are not required to determine the adequacy of heating systems, they should at least note whether there are heat vents, radiators or other heat outlets in the room before deciding whether to include space as living area.

When an area that is not part of the living area (e.g., a garage) shares a common wall with the living area, treat the common wall as the exterior wall for the living area; therefore, the measurements for the living area will include the thickness of the common wall, and the measurements for the other area will not.

Interior space that is open from the floor of one level to the ceiling of the next higher level is included in the square footage for the lower level only. However, any area occupied by interior balconies, lofts, etc. on the upper level or stairs that extend to the upper level is included in the square footage for the upper level.


The amount of living area and "other area" in dwellings is based upon exterior measurements. A one hundred-foot-long tape measure is recommended for use in measuring the exterior of dwellings, and a thirty-foot retractable tape for measuring interior and hard-to-reach spaces. A tape measure that indicates linear footage in "tenths of a foot" will greatly simplify your calculations. For best results, take a partner to assist you in measuring. But if you do not have someone to assist you, a screwdriver or other sharp tool can be used to secure the tape measure to the ground.

Begin at one corner of the dwelling and proceed with measuring each exterior wall. Round off your measurements to the nearest inch (or tenth-of-a-foot if your tape indicates footage in that manner). Make a sketch of the structure. Write down each measurement as you go and record it on your sketch. A clipboard and graph paper are helpful in sketching the dwelling and recording the measurements. Measure living area and "other area," but identify them separately on your sketch. Look for offsets (portions of walls that "jut out"), and adjust for any "overlap" of exterior walls (Fig. 3) or "overhang" in upper levels ( Fig. 5).

When you cannot measure an exterior surface (such as in the case of attics and below-grade areas), measure the perimeter walls of the area from the inside of the dwelling. Remember to add six inches for each exterior wall and interior wall that you encounter in order to arrive at the exterior dimensions (Fig. 2, 3, 4, 6).

Measure all sides of the dwelling, making sure that the overall lengths of the front and rear sides are equal, as well as the ends. Then inspect the interior of the dwelling to identify spaces which cannot be included in living area. You may also find it helpful to take several photographs of the dwelling for later use when you return to your office.

View Attachments for Figure Illustrations

Calculating Square Footage

From your sketch of the dwelling, identify and separate living area from "other area." If your measurements are in inches (rather than tenths-of-a-foot), convert your figures to a decimal as follows:

1" = .10 ft.
2" = .20 ft.
3" = .25 ft.
4" = .30 ft
5" = .40 ft.
6" = .50 ft.
7" = .60 ft.
8" = .70 ft.
9" = .75 ft.
10" = .80 ft.
11" = .90 ft.
12" = 1.00 ft.

Calculate the living area (and other area) by multiplying the length times the width of each rectangular space. Then add your subtotals and round off your figure for total square footage to the nearest square foot. Double-check your calculations. When in doubt, recheck them and, if necessary, re-measure the house.

Attached Dwellings

When measuring an "attached" single-family home (e.g., townhouse, duplex, condominium, etc.), use the same techniques just described. If there is a common wall, measure to the inside surface of the wall and add six inches. [Note: In the case of condominiums, do not include the thickness of exterior or common walls.] Do not include any "common areas" (exterior hallways, stairways, etc.) in your calculations.

Proposed Construction

For proposed construction, your square footage calculations will be based upon dimensions described in blueprints and building plans. When reporting the projected square footage, be careful to disclose that you have calculated the square footage based upon plan dimensions. Therefore, the square footage may differ in the completed structure. Do not rely on any calculations printed on the plans.

Agents' Responsibilities

Real estate agents are expected to be able to accurately calculate the square footage of most dwellings. When reporting square footage, whether to a party to a real estate transaction, another real estate agent, or others, a real estate agent is expected to provide accurate square footage information that was compiled using these Guidelines or comparable standards. While an agent is expected to use reasonable skill, care and diligence when calculating square footage, it should be noted that the Commission does not expect absolute perfection. Because all properties are unique and no guidelines can anticipate every possibility, minor discrepancies in deriving square footage are not considered by the Commission to constitute negligence on the part of the agent. Minor variations in tape readings and small differences in rounding off or conversion from inches to decimals, when multiplied over distances, will cause reasonable discrepancies between two competent measurements of the same dwelling. In addition to differences due to minor variations in measurement and calculation, discrepancies between measurements may also be attributable to reasonable differences in interpretation. For instance, two agents might reasonably differ about whether an addition to a dwelling is sufficiently finished under these Guidelines to be included within the measured living area. Differences which are based upon an agent's thoughtful judgment reasonably founded on these or other similar guidelines will not be considered by the Commission to constitute error on the agent's part. Deviations in calculated square footage of less than five percent will seldom be cause for concern.

As a rule, the most reliable way for an agent to obtain accurate square footage data is by personally measuring the dwelling unit and calculating the square footage. It is especially recommended that listing agents use this approach for dwellings that are not particularly unusual or complex in their design.

As an alternative to personally measuring a dwelling and calculating its square footage, an agent may rely on the square footage reported by other persons when it is reasonable under the circumstances to do so. Generally speaking, an agent working with a buyer (either as a buyer's agent or as a seller's agent) may rely on the listing agent's square footage representations except in those unusual instances when there is an error in the reported square footage that should be obvious to a reasonably prudent agent. For example, a buyer's agent would not be expected to notice that a house advertised as containing 2200 square feet of living area in fact contained only 2000 square feet. On the other hand, that same agent, under most circumstances, would be expected to realize that a house described as containing 3200 square feet contained only 2300 square feet of living area. If there is such a "red flag" regarding the reported square footage, the agent working with the buyer should promptly point out the suspected error to the buyer and the listing agent. The listing agent should then verify the square footage and correct any error in the information reported.

It is also appropriate for an agent to rely upon measurements and calculations performed by other professionals with greater expertise in determining square footage. A new agent who may be unsure of his or her own calculations should seek guidance from a more experienced agent. As the new agent gains experience and confidence, he or she will become less reliant on the assistance of others. To ensure accuracy of the square footage they report; even experienced agents may wish to rely upon a competent state-licensed or state-certified appraiser or another agent with greater expertise in determining square footage. For example, an agent might be confronted with an unusual measurement problem or a dwelling of complex design. The house described in Figure 8 in these Guidelines is such a property. When an agent relies upon measurements and calculations personally performed by a competent appraiser or a more expert agent, the appraiser or agent must use these Guidelines or other comparable standards and the square footage reported must be specifically determined in connection with the current transaction. An agent who relies on another's measurement would still be expected to recognize an obvious error in the reported square footage and to alert any interested parties.

Some sources of square footage information are by their very nature unreliable. For example, an agent should not rely on square footage information determined by the property owner or included in property tax records. An agent should also not rely on square footage information included in a listing, appraisal report or survey prepared in connection with an earlier transaction.

In areas where the prevailing practice is to report square footage in the advertising and marketing of homes, agents whose policy is not to calculate and report square footage must disclose this fact to prospective buyer and seller clients before entering agency agreements with them.


For assistance in calculating and reporting the area of homes, refer to the following illustrations showing the living area shaded. To test your knowledge, an illustration and blank "Worksheet" for a home with a more challenging floor plan has also been included. (There is also a completed "Worksheet" for the Practice Floor Plan.) In reviewing the illustrations, assume that for those homes with basements, attics, etc., the exterior measurements shown have been derived from interior measurements considering walls and partitions. Where there is a common wall between living area and other area, the measurements shown in the illustrations include the thickness of the common wall in living area except in the condominium example where wall thickness is not included.

*The following materials were consulted in the development of these Guidelines:
The American National Standard for Single-Family Residential Buildings:
Square Footage-Method for Calculating approved by the American National Standards Institute, Inc.
House Measuring & Square Footage published by the Carolina Multiple Listing Services. Inc.;
Materials compiled by Bart T. Bryson, MAI, SRA, and Mary L. D'Angelo.

View the Attachments for these Illustrations

    • Related Articles

    • Section 1.1.5 Square Footage:

      The reported square footage for all properties shall be measured in accordance with the NC Real Estate Commission’s guidelines that are incorporated by this reference and attached as Exhibit 6. Where square footage in the property meets all of the ...
    • Exhibit 7: Definitions

      Definitions and Explanations of Data Fields TERM FLEX LABEL SINGLE FAMILY # of Bedrooms Must meet the following criteria: 1. Must be included in the Primary Living Area 2. At least half the room must have ceiling height of 7 feet 3. Must have ...
    • Square Feet Range

      Choose an appropriate range based upon the calculation for heated square footage. See Exhibit 6 of the MLS Rules and Regulations.
    • Heated SqFt

      Measure, calculate and disclose per MLS adopted NCREC Residential Square Footage Guidelines Exhibit 6Measure, calculate and disclose per MLS adopted NCREC Residential Square Footage Guidelines Exhibit 6
    • Eff. Average Square Footage

      Eff. = Efficiency: a small apartment consisting of one room that includes kitchen facilities and a separate bathroom